What is this substance made out of and why hasn't anybody tried to reverse engineer it?https://www.youtube.com/watch?v=Ys-RMVJ89dkSeems like it could be candle wax and very fine metal powder. The entire casting machine seems like a load of bullshit. The powder they use seem to activate with the machine and it doesn't seem to do anything for the powder to turn into a liquid. The liquid's not hot enough to burn anybody touching it. It hardens rather fast and burns away in the crucible. So I think it's just candle wax and metal particles. I can't figure out what they're using for filling the crucible though. I think it's graphite powder, but honestly I have no idea.Great invention though.The casting moulds can be 3d printed and all you'd need is a oven to melt the particles together. For small metal prints you can just use the microwave glass melting kilns.Any thoughts on this?
>>3013950And the microwave kilns I speak of are like this. They're used for melting glass. But I'm thinking just flipping it upside down, filling it with graphite and the wax/metal model.What could possibly go wrong?
>>3013950You like... super high rn?
>>3013960No, I'm just very stupid. And european.But I'm not stupid enough to pay 2500 USD for a machine which appears to just melt wax.Seriously look at this:https://actionbox.ca/collections/action-box-machines/products/injekto-m
>>3013964You don't put metal in a microwave anon. Idk shit about the thing you poasted but if it is a wax with suspended metal particles you could accomplish that with a damn heat gun or you could make a hot water coil
>>3013950an excellent way to over complicate and maximize cost while making an inferior product.get a bucket, some ferro cement, a propane torch, and some air.Crucible can be steel for soft metalslike $40 and scrap
>>3013964It's sintering, and makes a porous substance that shouldn't be called metal really. mechanically useless
>>3013950>>3013952>>3013964Wax-powder sintering has been around for a while. The big issue of it is that when the binding material burns away your "green" molded part shrinks really considerably and non-uniformly. Their website advertises ~12% shrinkage. They also say you will get a ~11% density loss compared to solid parts. So you lose a lot of strength and it's difficult to estimate final dimensions. They're also using 3D printed molds so you can throw tolerances even further out the window. Lastly, the cost. They charge nearly $50/lb for this stuff, and you're losing 12% of that. So it's like a 10x markup compared to solid material. The process is relatively clean and fire-safe compared to sand casting but that's about the only advantage.
>>3014303Pretty much sums it up. There's no secret to this, it's just powder metallurgy being marketed to home gamers/small shops. It's not casting, and has major process caveats that casting doesn't. The main advantage is that its VERY fast, since one mold can easily stamp dozens of green parts a minute and they can be sintered thousands at a time. But that's production work, not hobbyist/job shop stuff.Never even mind the expense of the powders themselves, which are way more expensive than simple ingots of raw alloy.>>3014121>mechanically uselessOne of the biggest uses of PM is gearboxes, so IDKWTF you think you're on about. Not as good, volume for volume, as a forged and ground gear, but 70% as good for <10% of the cost is an attractive trade, to say the least.
>>3014312>One of the biggest uses of PM is gearboxesnot the play-doh fun factory gunk."Sintered copper from a paste generally achieves 85% to 90% of the density of cast copper."and the 12-15% shrinkage would make it useless for parts. Couldn't do complex parts like slurry casts. Also has worse conduction than cast, if that's your thing. Couldn't do complex parts like slurry casts.
>>3014383Shrinkage isn't really an issue for most use cases. You design the green part 10-15% bigger(whatever the material specs call out for X-Y and Z shrinkage) and then post process machine to final dimensions. It's a lot like working with a casting, but alot cheaper when you just want one off or prototype parts.