[a / b / c / d / e / f / g / gif / h / hr / k / m / o / p / s / t / u / v / vg / vm / vmg / vr / vrpg / vst / w / wg] [i / ic] [r9k / s4s / vip] [cm / hm / lgbt / y] [3 / aco / adv / an / bant / biz / cgl / ck / co / diy / fa / fit / gd / hc / his / int / jp / lit / mlp / mu / n / news / out / po / pol / pw / qst / sci / soc / sp / tg / toy / trv / tv / vp / vt / wsg / wsr / x / xs] [Settings] [Search] [Mobile] [Home]
Board
▼ Settings Mobile Home
/diy/ - Do It Yourself

Name
Options
Comment
Verification
4chan Pass users can bypass this verification. [Learn More] [Login]
File
  • Please read the Rules and FAQ before posting.

08/21/20New boards added: /vrpg/, /vmg/, /vst/ and /vm/
05/04/17New trial board added: /bant/ - International/Random
10/04/16New board for 4chan Pass users: /vip/ - Very Important Posts
[Hide] [Show All]


[Advertise on 4chan]


File: wg.jpg (169 KB, 1424x1058)
169 KB JPG
Any HVACfags here?

House furnace. It powers on. Blows only "cold" air.

>Code 33
>New filter
>Flow to vents is unchanged (should be fine)
>I Pulled power for a reset
>I Pulled and cleaned the Flame Sensor
>House has natural gas to other stuff

There is no burner action, ever. No smell of gas, and no sight of the ignitor doing anything.
Inducer motor will come on immediately when the unit sees power. The other motor, nothing.

Maybe big clue: Is 62f here and 66f interior, I put AC on to 61f and nothing happens.
>>
>>3015915
"Code 33" means fuckall without knowing the board.
>>
File: 1000033521.jpg (3.66 MB, 2252x4000)
3.66 MB JPG
>>3015917
Code 33 seemed to be universal, along with all the other codes.
>>
On your **Payne PG8MAA042090ADJA** furnace, a **Code 33 generally means a limit circuit fault**.

The furnace is detecting that a safety limit switch has opened, usually because the furnace is overheating or airflow is insufficient.

The furnace may shut off the burners while continuing to run the blower to cool itself down.

### **Most common causes, in order I'd check**

1. **Dirty air filter** – Replace it if there's any doubt.
2. **Blocked airflow** – Make sure supply registers and return-air grilles are open and unobstructed.
3. **Blower problem** – Weak blower motor, bad capacitor, loose blower wheel, or dirty blower wheel.
4. **Restricted exhaust vent** – Check for visible obstructions at the exterior vent termination.
5. **Bad limit switch or wiring** – A defective switch or loose connection can trigger the code.
6. **Flame rollout or blocked-vent safety switch** – These are more serious safety faults.

### **What I'd do first**

- Turn the thermostat to OFF.
- Check or replace the furnace filter.
- Make sure all supply and return vents are open.
- Check that the furnace blower is actually running.
- Let the furnace cool and see whether it operates normally afterward.

Important safety warning

Don't bypass any safety switches. If a rollout switch has tripped, don't simply reset it. That can indicate a combustion or venting problem that needs professional attention.

If code 33 persists for more than 3 minutes, the furnace can transition to code 13 (limit circuit lockout). 
### **A couple questions to narrow it down**

1. Is the furnace blowing cold air continuously, or does it heat for a while and then shut the burners off?
2. Does the blower keep running when the burners shut off?
3. Is this a new problem, or has it been happening intermittently?

I can walk you through narrowing down whether this is an airflow problem, blower problem, or limit-switch issue without having you mess with any dangerous gas components.
>>
>>3015948
Thanks ChatBBC!
>>
>>3015950
Any time meatbag! Check those limit switches you gay baby



[Advertise on 4chan]

Delete Post: [File Only] Style:
[Disable Mobile View / Use Desktop Site]

[Enable Mobile View / Use Mobile Site]

All trademarks and copyrights on this page are owned by their respective parties. Images uploaded are the responsibility of the Poster. Comments are owned by the Poster.