>>28979010
Nothing because I dont drive piece of shit dodges.

>>28979010
>replace O2 sensor
>adjust fuel maps
>rewrite part of launch control program
>investigate occasional clunking sound in rear

>>28979093
you saynl that like you don't drive one of them little tykes cars.

>>28979093
what kind of bus do you ride?

>>28979010
I changed a brakeline yesterday since some fuck decided to ziptie calix cable on the brakeline and other wiring and it rubbed on power steering pump

>>28979093
lets see your engine bay, anon

File: 1781019723769.jpg (171 KB, 700x394)

171 KB JPG

>>28979010
>reman compressor

>>28979010
Is that someone zip-tying a plastic bag to an A/C line to “cover” a leak?
Or is there a hidden scooby snack in the bag?

>>28979300
previous owner bought the wrong compressor, bag is for keeping the lines debris free

also, nice dubs

File: Carly top end rebuild.jpg (1.21 MB, 8160x4592)

1.21 MB JPG

Absolutely fucking nothing, apparently, just a day of one step forward and two steps back. First cock up was when I came to undo the very last head bolt, which is against the firewall and extremely awkward to get an angle on - rounded the bolt head and needed to buy an extractor set to get it out. Second cock up was putting the head back on - the bolts are torque to yield and have a 20nm + 180° + 5° torqueing setup, which of course I fucked by slipping on the last bolt, knocking the angle gauge and completely losing what angle I was at. I'm not entirely confident the other bolts are even at the right torque either though, as the gauge is so damn awkward to use that I think I tightened them a tad too much to begin with. Regardless, turns out it was all for naught anyway, because I completely forget to replace the valve stem seals that came with the gasket set! Absolutely fucking exquisite work on my part~

>>28979880
jesus christ

File: pop goes the ball joint.webm (449 KB, 1920x1080)

449 KB WEBM

>>28979010
Did muh lower front ball joints.

File: arms.jpg (477 KB, 2000x1500)

477 KB JPG

>>28979984
Followed by upper control arms so I can finally get rid of that S T A N C E D camber that's been eating tires for the last 20 years lowered.

File: boners.jpg (534 KB, 2195x1646)

534 KB JPG

>>28979991
A couple of my oopsie doopsie fucksy wucksys.

File: 15422.jpg (1.35 MB, 2035x2623)

1.35 MB JPG

Wheel hub assembly, low pressure fuel pump, 02 sensor.

>>28979010
replacing the radiator. current one is pretty clogged and nobody rods out radiators anymore, they only want to do a full recore which will cost an insane amount of money which is only worth it if you're doing a 1000 point restoration.
gonna use this radiator to have a go at desoldering and rodding it out myself.

File: Keith_Sapsford_falling_ou(...).jpg (8 KB, 250x161)

8 KB JPG

>>28979010
Definitely not my life
Probably not the lawn ornaments I already own
No it's gotta be some new strange
something that looks terrible on the outside
but feels tight and cozy on the inside
while it wastes my money and time
until it leaves me like everything else
>4chan can't get near my new van it'll explode

File: file.png (1.55 MB, 1224x701)

1.55 MB PNG

>>28979010
Bought the car to sell it for monies

>>28980134
The fuck is this? Why is the engine so low? Does the intake manifold take up half the engine bay?

File: GV 1.6.png (1.29 MB, 1269x706)

1.29 MB PNG

>>28980136
Suzuki Grand Vitara 2008 with 1.6L

Tiny I4 in an engine bay thats built to be able to fit a 3.2L V6 = so easy to work on. Was taking my sweet time and working slowly and even then it only took about 3 hours to get the head off

nothing because it's 85 degrees and 67% humidity

A fan for my grandmother. My car is fine.