WEEKEND RENCHING GENERALSpoke Too Soon Edition
Are walmart batteries typically this crap? I bought one 17 months ago and it's dying already. (Checked alternator and checked for current draws, car is an 8th gen civic driven on 1hr commute 4 days/week)
>>29126109>pulled windshield, addressed rust in preparation for a new windshieldSafelite was supposed to come today. >>29126114I've had terrible experiences with the everstarts.
>>29126114It's Walmart? What did you expect?
>>29126109Been doing work at my rental property. Sanded down these cabinets, 1 coat of stain, and 3 coats of polyurethane. It'd look better with more coats of polyurethane, but I've already put it too many hours, so I'm calling it good.
i have been cooped up in my apartment bored out of my mind for so long that i'm genuinely considering calling up a friend of my grandma's and offering to "fiddle with" his car that's been parked halfway under a tree on his property for a dozen years while also having exactly zero mechanical experience.if there were literally any jobs within walking distance that would hire me other than retail cashier i would be working one of those right now instead of even humoring this idea.
It's so over...
>>29126844What happened? Did the HG fail here and that area is warped now?
Gotta replace this (and the other half of it) with the new guy.Any tips for the nuts threading it onto the studs at the exhaust manifold?I got a 6 point socket, an impact, a breaker bar and I'm marinating it in pb blaster as we speak.Those fuckers were tight enough I was sure that the stud was gonna let go, so I quit, sprayed it down and have proceeded to wait. I also have a propane torch.
I'm retarded>>29126956
>>29126114 In my experience?-In the past 15 to 20 years, "cheap" batteries have gotten much worse, middle of the road stuff is where cheap used to be, and "premium" is on the way out.Cheap batteries in the U.S. market were often made in Mexico, some parts of Eastern Europe, or Southeast Asia. They were usually "good enough" for around three to five years of common use before they'd drop a cell or short out.Now it's all made in China or India, and they're just unpredictable. Some will almost be as good as the old stuff, some will fucking die in a week.
>>29126844Grim. How deep in the hole are you already?
>>29126951It's eroded from combustion heat and pressure moving between the two jugs.
>>29126956Heat, PB, take a small hammer and a punch and tap on it. If you're not in a hurry, give the penetrant time to work and apply it often. You can use a drop light with an incandescent bulb or heat bulb to keep that area warm and help it seep.The impact is probably going to break shit. Judging by that downpipe, you're going to be dealing with broken studs anyhow.
>>29126976I'll hose em down some more and get to tappin. Honestly I think they might come off
>>29126984Spoke Too Soon Edition
>>29126984>>29127052Fire is always the answer. A blow torch and an impact is the best way, and if it snaps off with that combo, then you had no chance anyway.
>>29126114Project Farm did a battery test like 3 months ago. Todd concluded that WALMART batteries suck.
>>29127161Sad it only covers Oreilly and Walmart. I just bought an Autozone one. Hope it lasts.
>>29126971Not at all, the HG blew and I've just pulled and disassembled the engine yesterday. Now I'm debating whether to buy a new head from aliexpress for around 350 euro or get a machine shop to weld and machine it for unknown amount of money.
>>29127052Sorry to see bud.Well, hope you're up on broken fasten extraction.Good LH drill bits are your friend.
>>29127052well... it came off
>>29127756>>29127756I have the nastiest jury-rig imaginable going on right now but the exhaust system is sealed(ish) and quiet.Gonna get some map gas for the manifold and have a buddy weld on a big nut. We'll get her done. If you learn a little something, did you really fuck up *that* much?
>>29126518>decide to look into the paperwork side of it>realize that for either of us to legally do anything with the car beyond make it start and run in his driveway i'd need to somehow get him out of his "conservatorship" he's got himself into that is practically trying to unperson him and steal all that he ownsall this for a chevy celebrity that's nearing 40 by the way
>>29126969It's not just the cheap ones. Some recent Toyotas in Europe shipped with a Varta branded battery that was probably made in a sweatshop in Turkey or India.For a while, Toyota topped the vehicle unreliability charts, basically entirely due to 12 V batteries that die with no warning after a couple years. No other problems with the cars, it's just that they won't go anywhere if the 12 V battery has dead cells and can't even power the dashboard.Think they at least changed the supplier after that.
>>29128895>chevy celebrityI think these had a transverse v6 that put the spark plugs right up against the firewall, and there's not enough room for tools. I think it's one of the worst cars you could possibly choose to work on.get one of those mechanic simulator games, or my summer car or something
>>29129132i looked it up earlier and they can have those or a 2.5l i4, and i'm like 99% sure that his has the i4. i'll be over at his place either later this week or the next to see for myself and if it does have the v6 i'll probably throw in the towel>get one of those mechanic simulator games, or my summer car or somethinglike 75% of the reason i'm considering doing this isn't to have a car, but just to have something to do outside of my bedroom. i spent all summer cooped up in here being a lazy piece of shit playing vidya and jacking off and i want to change that in a way that won't result in me being stuck in a checkout kiosk interacting with middle aged single mothers for 8 hours a day, the car is just a bonus
What say you, guys. Is it screwed big time?
>>29129639Nah, that'll clean up fine.
Decided to fix the trans leak on the ambulance.>I've been ignoring it for months after seeing the massive puddle it left. >Mishimoto deep pan was ~5qts lowI think I'm going to fix the couple minor issues it has and sell it.>>29126170>new Kerma smic, charge pipes>new brembo pads/rotors, soft lines, 1 new hard line, pressure bled>stops greatShould've replaced the soft lines years ago. What a difference. >pedal now feels incredible>>29126984The hotrod Induction heater has been one of my favorite Amazon purchases. Makes situations like that an absolute breeze.
I am going to lap valves for the first time and I am nervous.
>>29131839Why? You can't really fuck it up if you're doing it by hand with paste
>>29131839Oof, I offer you luck. Try to reapply the paste semi-frequently as it will naturally push out to the edges of the valve, creating a convex/concave hotspot if lapped for too long. Other than that, it's a pretty easy, if monumentally boring job...
>>29131847Because it is a teeny 14mm valve so it might be easy to overdo it. I decided to replace the valve >>29129639 since it was only 30 dollars. I'm thinking of leaving the intake alone since it still seals fine.>>29131849So about every other time stop grinding?
>>29131863>So about every other time stop grinding?When the sound changes is when the paste has evened out, and 10 or so seconds of back and forth and up and down after the sound change is when I like to reorganise the paste. If your valves are brand new, then you don't really need to lap them for very long, maybe a minute or so with a fine paste. I like to reassemble the valve and spring, then spray some brake clean on the back of the valve to see if it leaks after. If you're lazy, then you can also just pull the valve shut, shine a light through the port, and see if there are any gaps on the head / face of the valve, but the brake clean is a little more reliable in my eyes as it's quite thin and will weep through easily. Oh, and remember to oil the valve stem every time you reorganise the paste, it'll you chewing up your stem seal.
>>29131915>it'll you chewing up your stem seal.It'll *stop* you chewing up your stem seal.
Has anyone ever replaced the rear springs in a w123 wagon with the hydraulic suspension? Is it any worse than the front?
I'm switching from rubber to silicone coolant hoses. Should I stick with spring clamps like it came from the factory?, or should I switch to worm/T-bolt or some other kind?
>>29133147>silicone coolant hosesKeep in mind that silicone hoses are very slightly permeable and the water in the system will slowly wick out over time. Not an issue if you check your coolant every few months, but it's just something to keep in mind if you see the level drop with no obvious signs of a leak.Anyway, If they still fit, I'd stick to spring clamps. If there are plastic lines you're connecting to, the spring clamps will *in theory* allow the plastic some degree of expansion as the coolant heats up, preventing the plastic from cracking under the pressure of the clamp. Worm/t-bolt clamps obviously don't allow for this, though admittedly I have yet to see a failure because of it.
Lapping is finally tackled. You can't see it but there is rubbing alcohol in there and hasn't budged :)
>>29129132>>29129140haven't been able to get over to his place because we've both been busy but i just got confirmation that it has the i4 AND that he'll give it to me fully in my name as a gift and i won't have to pay him a centon the legal/paperwork side, we're gonna have to go down to the local DOL together and get a new title and try to get that new title in my name, because he forfeited the original title to his insurance company but kept the car, and apparently state laws let you retitle a vehicle after you do that, but some people online say doing that requires an inspection while others online say they didn't need to when they had it done, AND he might have lost the insurance paperwork about him giving up the title but keeping the car, so we might need to get THAT reprinted toohonestly when i was first thinking about this project i expected to be spending more time cleaning out rat nests and less time trying to understand the law around this extremely fringe case i've gotten myself into
>>29137278>got over to his place finally>surface rust on roof>think "ok thats fine">rear driver-side door is dented in and won't open>think "ok i already knew that">this has caused the driver door to become jammed shut as well>think "well at least the passenger-side doors still work">the passenger side is currently functioning as a structural support for his fence that's collapsing onto it and as such cannot be easily accessed>AND he forgot to find the key before i came over>think "maybe this car wasn't the best idea">look closer at the interior through the window>steering wheel and rear footwells are covered in mold>mfwi think i'm gonna spend a few days looking on facebook marketplace and see if i can find a shitbox for under like $1.2k or something before i think about going down to the DOL to try and work out how to get this fucking mess a title, i would probably see all of these issues as just fine if it was just this and not this plus a paperwork headache
>>29126844We're so backEntering my boyracer era at 27 years of age
I have an old Shitbox truck with manual transmission.It feels like there's slack somewhere in the drive train. Moving forward under power, smooth.Gently remove foot from gas, jerk, coast against the engine. Re apply foot to gas as gently as possible, jerk, pushed forward by engine. Problem is worse at lower rpm, and I know this is normal to a degree, however there is a very noticeable "slack" feeling as the strain on the drivetrain moves from acceleration to deceleration. I have plenty of experience on manual transmissions, cars and motorcycles and I have never felt this much slack between accel and decel. Please, can someone point me in the right direction?Truck is at 265k, and almost entirely original as far as I can tell. Something's worn out, I just know it, but I don't know where to start looking.
The ball joint fought me, had to take the fuckin knuckle and strut off too
>>29140346that bend going in to the intercooler though...i think you could see a bump in power (or at least flow) if you could make it more curved
>>29137278>>29139399>thinks a 40 year old Chevy will be in any good conditionThis is your brain on GM.
>>29143577i knew it was gonna be bad, i just didn't know it was gonna be so bad that it was being used as a load bearing element of a fence and that the top of the trunk was being used as a place to store firewoodif i haven't gotten a call from one of my other relatives by tomorrow like they said they would then this'll still be my best option for getting a set of wheels, unfortunately
>>29126109Anyone have any tips for working on their car while living in a major city?I sometimes do a little bit here and there like I replaced the drive belt and about 15 people stopped to ask about the car/what I was doing which was really nice and cool but also meant I spend most of the time talking to people rather than doing any work.Could I drive to a supermarket carpark and do it there or something? Or would that look suspicious as fuck?
>>29144060Some people do it right in front of autozone
>Installing piston rings>All gaps are perfectly in spec except oneI should have seen this coming.
>>29142861engine mounts could it be perchance
>>29143520What vehicle? I recently confirmed a torn boot on a ball joint that I suspect is causing a clunking noise in certain situations. My example is quite rusted and the procedure to remove it from the knuckle seems prone to difficulties. It's a T45 Torx head bolt with a 15mm nut that squeezes the knuckle and interfaces with a groove on the ball joint stud. I've heard the bolt can seize in there. See: https://youtu.be/ETmIvIpo15E?t=39
Does anyone know of any replacement for the exhaust manifold bolts on a 5.7 HEMI that won't snap?
>>29143701>said relative (grandma) misunderstood what i meant when i told her that "WE (me and my mom) need a car, tell rich uncle this" and apparently assumed that my currently-licenseless ass would be the one driving the car as soon as we got it>grandma ended up telling rich uncle that *I* need a car instead of *WE*>rich uncle then seemingly assumed my mom already had a car and as such his response to my grandma was just "have him go get his license first"i've been saying "i" and "me" this whole time on here when talking about the rusty shitbox celebrity because i thought the fact that this car would technically be my mom's (while being registered in my name) wouldn't ever be of relevance here>inb4 why the fuck are you trying to get a car before a drivers license you dipshit retard cart-infront-of-the-horse-ass faggotthe original plan for me getting my license was for my mom to get a car (financed by my grandma since we're both broke) and then have her teach me some of the basics of driving so i wouldn't have to pay for driving school lessons, and then she could effectively "retire" from driving, but that was over 2 years ago now and talks between those two have went nowhere (every woman in this family is the putting-shit-off-forever champion) and i'm going insane from boredom at this pointtl;dr never ever rely on other people to ask for things on your behalf. sorry for blog.
I got my midpipe in but the studs on my header are fucked from trust so I ordered a catless 4-1 race header. I'm just going to leave my car on the stands till it gets here. Gonna start working on the bosozoku axel back portion tomorrow but I've never tig welded before. I'm sure it'll be fine
One of the rear wheel cylinder bleeders on my shitbox is absolutely fucked. It's so rusted away it's almost unrecognizable (pic rel). Seems like a previous owner cheaped out and just one side was replaced in the past.Think I can get the factory hard line out intact on the crusty side to replace the wheel cylinder?
>>29147753Probably not, but If you heat the ever loving fuck out everything and dowse it in WD or similar after, I can see it being possible. God speed, anon, be sure to update us on how it goes~