[a / b / c / d / e / f / g / gif / h / hr / k / m / o / p / r / s / t / u / v / vg / vm / vmg / vr / vrpg / vst / w / wg] [i / ic] [r9k / s4s / vip / qa] [cm / hm / lgbt / y] [3 / aco / adv / an / bant / biz / cgl / ck / co / diy / fa / fit / gd / hc / his / int / jp / lit / mlp / mu / n / news / out / po / pol / pw / qst / sci / soc / sp / tg / toy / trv / tv / vp / vt / wsg / wsr / x / xs] [Settings] [Search] [Mobile] [Home]
Board
Settings Mobile Home
/diy/ - Do It Yourself


Thread archived.
You cannot reply anymore.


[Advertise on 4chan]


File: this way.jpg (134 KB, 1080x1350)
134 KB
134 KB JPG
Use this thread to ask questions you think don't require a thread of their own.

The old thread no longer bumps and is on page 5 now: >>2863207

If you didn't get a response in the old thread, feel free to ask again here.
>>
>>2868928
why do you keep making these shit threads? JK IDC
>>
>>2868984
It's a shitty job but someone has to do it.
>>
yeah but 3/4 of the catalog is a stupid question. trannyjannies don't enforce it. what's the sense?
it's like jerking off with a clothespin on the end. it's not getting anyone anywhere.
>>
Either try to make it better or go elsewhere.
>>
I do a lot of my cooking on some small wire racks in my air fryer these days, and I'm wondering if there's a better way to clean them. Standard scourers are a bit of a pain to get in-between the rack, I bought some fake scrub daddy shit which works well, but they fall apart fairly fast, only last a month or so. The racks are made of stainless steel, and I've heard that shit like steel wool will eventually cause rusting. Brass scouring pads might be a good choice, does anyone use that shit?
>>
File: IMG_2411.jpg (96 KB, 1170x1631)
96 KB
96 KB JPG
>>2869180
I would find an ultrasonic cleaner with a big enough bath to fit your thing or stiff nylon brush.
>>
which trades are worse for male on male bullying esp for an estrogenized twink
>>
File: reusable parchment.jpg (107 KB, 1381x586)
107 KB
107 KB JPG
>>2869180
>a better way to clean them

easiest way to clean them is to never get them dirty
get some of these, cut them to size, punch a lot of holes, wipe clean after use
you can also use real parchment paper, already cut to fit, at the dollar store
>>
>>2869208
>worse for male on male bullying

all tradesmen will find you equally revolting
dont even consider it
>>
I bought a cheapass serpentine belt installer tool off rockauto and I need to file off like, 1/8in from the end of it because it's still not narrow enough to fit where it needs to.

What's the best cost/convenience ratio for whittling it down? Is just about any file going to be good enough for the job? Should I just give in and buy a bench grinder or similar?
>>
>>2869246
I use the wire racks so I can double stack food in the small compartment, so paper would block the airflow I use the racks to facilitate.

I have used paper in the bottom before, but a silicone liner worked better.
>>
>>2869254
Hacksaw. A file will eventually work, but 1/8th is about the amount of material I wouldn't want to have to file. Bench grinders are nice to have, and angle grinder would probably do it too but be a little more awkward.
>>
File: cover.jpg (122 KB, 848x812)
122 KB
122 KB JPG
How do you clean your wash/dry machine cover?
>>
>>2869254
Can you do it with some crowsfoot combination?

Otherwise anything that grinds should work:
>>
>>2869262
I spray mine off with the hose outside on the deck then let it air dry on the clothesline every other day. Used to do it daily, but then I started door dashing as my second job so I don't have time for that now.
>>
>>2869274
>>2869260
The tensioner accepts a 3/8 square drive head. If it wasn't such a tight space a standard ratchet would do it. The tool I bought might even have fit but there's also some welding bumps where the 3/8 is welded in.


https://www.rockauto.com/en/moreinfo.php?pk=8760724&cc=0&pt=431

tool in question. Car is a 2007 impala ss 5.3l
>>
>>2869275
I was thinking of drowning it in some cleaning substance. It doesn't seem practical tho.
>>
>>2869282
Is that a transverse V8? Damn anon, I feel for ya. You can’t get in there from the wheel well? Or loosen a motor mount and get the jack on there and tilt it enough to fit the tool in there?

Otherwise modify the tool. How do people on the Youtubes get the tensioner loose on those cars?
>>
>>2869309
It is. Tubers go in from the wheel well and just hook a prybar on the spring and pry it down, which didn't get me enough clearance on the belt, or they use a hose clamp to do the same thing. I don't want to put my faith in a hose clamp so I'm just filing the tool down.
>>
>>2869247
can they not be nigger at least
>>
I have an old air variable capacitor, which seems to have a short once I turn it past a certain angle. I'm assuming two of the many plates are touching, but I don't know exactly where

Does anyone have any tips for finding the short so I can try to sand it down?
>>
>>2869331
>any tips for finding the short

pretty obvious answer:
if it's open-air, slide a thin piece of paper between plates to see where it catches
(weighing paper is very thin)

if it's enclosed in a plastic box, you'll probably destroy it trying to open it, so leave it alone
one goofy idea is to run a high current pulse through the short, by discharging a big cap
this will blow away any material that's shorting, and/or create a layer of isolating carbon
>>
File: images.jpg (12 KB, 299x168)
12 KB
12 KB JPG
I'm constructing a portable subwoofer for a small mobile sound system, that I already have.
Thr inner volume of my enclosure is 17l and it is meant for open air use.
I have it all simulated with a round port and the last thing to decide on is the port shape.

I have a 3D printer, so I can make any port shape I want. But I don't know which is best. Apparently exponential curvature has benefits over a straight pipe. I just don't know how to size it properly in relation to a straight pipe from the simulation.
Hexiblob made a video about this but he is just listing different port shapes and not telling when to use which and how to lay it out properly.
>>
>>2869422
Fuck if I only knew the hornets nest I stung into.
I finally found a paper on this topic, which helps me.
tl;dr
- optimal port shape is still an unsolved physical problem
- a continuously flared port is always better than a straight pipe
- best flare can be estimated

https://www.comsol.de/paper/optimal-design-of-bass-reflex-loudspeaker-ports-81561
>>
>>2869377
>>2869377
>slide a thin piece of paper between plates

Yeah I thought of this already, but there's a ton of plates. If anything, I'd use multiple pieces of paper at a time, removing them one by one to see if the short appears


It's installed in an old signal generator, but I can probably remove it, it'll just be a pain in the ass

And I have accidentally pulsed it a few times. While plugged in, it does work properly at certain frequencies, but once I turn it past the short, I hear the arc/pop and it stops outputting at any frequency until I unplug it and let the other caps discharge. It doesn't seem to have made a difference TWDDML
>>
>>2869422
>>2869429
The length of a flared port is just the length of the port tube, flares included. The flares themselves don't alter the length, and you don't have to consider the flares or include the size of the flares when measuring the length. You can just measure the length.

>Thr inner volume of my enclosure is 17l and it is meant for open air use.
What do you mean that the enclosure is meant for open air use? That doesn't make sense.

Have you already confirmed that your subwoofer performs well in a 17L ported box?
>>
>>2869312
Jesus christ this is an obnoxious fucking bit of maintenance. After misreading where the tool should slot in TWICE, failing to pry the spring down, I'm resorting to the hose clamp method...tomorrow.

Shouldn't have driven it with a fraying belt and should have just taken it to a mechanic.
>>
>>2869495
>The length of a flared port is just the length of the port tube, flares included.
thanks

>What do you mean that the enclosure is meant for open air use?
It's meant for outdoor use


>Have you already confirmed that your subwoofer performs well in a 17L ported box?
Yes, simulated it. Looking at the Dayton Audio DCS205-4. Actual volume is 18.5l but I subtracted the port and the driver magnet.
>>
>>2869208
Just get into any union in a blue state and you’ll ok, the PC conditioning is strong, can’t even borrow a pair of dykes without getting corrected.
>>
>>2869208
I think you might find a bf if you're in one of the chiller trades
>>
>>2869710
>PC conditioning
that's not the problem
i just don't understand why is everyone overly critical of your work like they're trying to prove they're a better craftsman than you when they're not even fully right seems kind of a dunning kruger thing except with nig types who haven't graduated high school
>>
>>2869715
nah i'm just shy and sensitive not homo
>>
>>2869716
>overly critical of your work
It’s called workmanship, so you might be missing the concept. Mexicans can get work done, craftsman take pride, do it right and then talk shit on everyone else. I’d make a work wife out of a femboy that could make a straight cut with a sawzall.
>>
>>2869734
craftsmen should know there is more than one way to skin a cat and what business do you have shitting on others when you're using some discount retarded way meant to prioritize something when i'm prioritizing something else
it just seems like bullying for sore losers kind of like those those boomers on youtube going i have 12 yrs in bla bla and there is only one way... fuck off it's like he just wants to hear himself yap
>work wife
sure if you're a lady i could fix your sucky work and let you take all credit
>>
File: adapter.jpg (72 KB, 1386x973)
72 KB
72 KB JPG
I need to power a big 200w LED panel for a few hours one night. We won't have access to electricity and it's not practical to lug a generator with us. I bought pic related thinking I could use my Tuscon as a generator instead, hooking the light up and letting the car idle. Should the alternator be able to keep up? Am I retarded? What do I don't know I don't know? Any suggestions?
>>
>>2869940
>200W

Your alternator should be able to handle that no problem. My concern is that inverter and the plug that goes into the lighter outlet. I would recommend going with a little bit better inverter with clamps that goes straight to the battery, there’s a good chance you could be blowing fuses trying to run 200W off that lighter plug.
>>
File: IMG_3375.jpg (195 KB, 960x1280)
195 KB
195 KB JPG
How much pressure can i apply to a cable?
According to the package, this spat in the baseboard is supposed to hold a cable, but it’s a very tight spot. And it’s just some rather old piece of cable I had laying around, most modern extension cords I have are much thicker, so I do t know if I can even buy a few meters long of “thin” 220V cable nowadays.
>>
>>2869963
Remove the sheath, use solid core rated for the load. Should fit fine then.
>>
>>2869964
Yeah, I could go for three strands, but that would be even further from code than doing it yourself.
>solid core
You mean just one thick piece of copper per strand? Probably hard to get. Plus, I gotta bend around some corners, so I’d rather go flexible.
>>
>>2869974
>You mean just one thick piece of copper per strand? Probably hard to get.
That's literally how all home wiring is done in first world countries. As long as you're not bending around extreme radiuses it works fine, a few 90 degree corners is no problem. Solid core can be much thinner and is much safer than multicore in applications where it isn't subjected to constant movement.
>>
>>2869975
I thought Multi Core is the standard nowadays since it won’t break as easily as single core, but could very well be that I’m wrong.
But I guess I’ll have to get what my local Baumarkt offers, since all the proper shops are closed on Saturday’s and only sell to professionals anyways.
It’s just gonna be an extension to the bed, so it’s never gonna see more load than a bedside lamp and a phone charger.
Well, maybe a thinkpad charger too, but that’s 100W max, I’m not gonna run my angle grinder in bed. But as long as I don’t get funny ideas using cables that are not meant for 220V, I’m gonna be fine.
>>
How does the stock carving machine in the beginning work, or more precisely, how does it transfer power from the rear mounted motor to the spindles on the moving slide? Is there a second motor mounted below on the slide? In my experience these older machines have just one motor so I'm confused.
https://youtu.be/MFVWmPkLO6Q
>>
>>2869953
>there’s a good chance you could be blowing fuses trying to run 200W off that lighter plug
this
considering the efficiency of the inverter, getting 200 watts will likely require around 20 amps - not something I'd want to try through the cigarette lighter/power outlet.
>>
>>2870017
>>
>>2869998
probably does have a second motor he seems to flip on two switches when he starts it up
>>
i broke my hip and my friend said he can get me permanent/lifetime disability plates on my car cause he has family at the dmv. this sounds like a great move becuase then i wont get tickets for stupid shit like street sweeping and metered parking, but i wonder if it will bite me in the ass if im trying to get a job that involves labor, or my car is seen constantly parked at the sports fiield and some hater sees me getting out of my car to play sports everyday. i have no intention of taking handicap parking spots, idk, what could go wrong?
>>
>>2869998
There are enough belts and sheaves on there that it could easily be only one motor.
>>
I was closing my oven when the door came off - no idea how, but no scary noises. I'd think it was my fault, but I have taken the door off in the intended way quite a few times before and this doesn't look or feel familiar, plus IIRC you can't close the door all the way with the locking levers open and I was using it at the time with no problem.

Now I think the hinge is in the position it's in when the door and lever are closed, even though that should have prevented the door from coming off. I can't move the hinges by hand at all, but if I shimmy the hinges back into the slots I can use leverage to open the hinges partway, but they slip and snap shut violently. Even if I could get the door back on and open (the position where the locking lever can usually be moved), I'm not sure I'd want to adjust the lever that's a fraction of an inch from these finger-eating springs.

a) clearly I'm dumb, so is there any way this could be a completely different issue from what I'm thinking?
b) what do?
c) since the manual claims the door can't be detached with the levers closed, can I even assume it'll be possible to attach it in that position?
d) even if I can get the hinges to the open position (with the door on or off the oven), how would I get the locking levers to the open position without cutting my fingers off?
e) would it be a bad idea to disassemble the door to try to put the hinges in the right position? I can only find one video of the door disassembly and it's for a model with different hinges (or at least different locking levers). I'd imagine it probably isn't a good idea to start loosening screws with the springs storing energy, and they might be if the door is off the oven even though it isn't supposed to be

Manual for reference https://media3.bsh-group.com/Documents/9001676944_A.pdf (page 13). I'd be happy to take pictures, but I'm not sure what I'd even be taking a picture of.
>>
>>2870033
If that were to even come up on a job application, I think you might be good because of all the ADA stuff, it would be akin to an employer not hiring you because you’re gay or black… two other crippling disabilities. They probably can’t even look into anything like that before an interview because of HIPAA in addition to the ADA, that would be big problems for any reputable employer.

If not, then you find a lawyer and get paid because the company violated the disability act.
>>
So im fixing a fan cable that broke while also retarproofing for kids, woman and a dog.
What would be the best way to fix it?

1)Put heatsrink cables, solder them back together and then cover then with tape and shrink the tubes?
2) faston?
>>
>>2869180
i bought an oven from a salvage yard that that was completely full of grease/burnt food

I put the racks in a plastic bag filled with oven cleaner (usually sodium hydroxide aka caustic soda) and let them soak overnight

if they are real (good) stainless caustic soda wont harm them at all

the reason steel wool causes rusting is because you basically smear non stainless steel onto the stainless which starts rusting and then kick starts rusting the rest of it, other times if it's really bad stainless (or 'i cant believe its not stainless', like 17-7 or 17-4 grade steel) then it will get surface rust regardless
>>
>>2870142
>Put heatsrink cables, solder them back together and then cover then with tape and shrink the tubes?

wtf, you use EITHER heat-shrink or tape, not both

the more important part is that the repair should be done where you cant access it
in other words, use a new cable, like an old computer cable, and solder it inside the fan case
>>
>>2869981
Whut? Unless you're flexing the solid core back and forth 180° 20x there's no way it's breaking lol. Multi core is shit. Shit to work with shit for resistance shit for resisting vermin shit all round.
>>
I recently bought a dremel for cutting and polishing mineral specimens I've collected. I use it outside wearing a half-face respirator with p100 filters and a household fan to blow dust away from me but was wondering if anyone has recommendations for dust suppression using water? There's a faucet near where I set up my bench so I don't mind nigger-rigging something to spray a small but constant amount of water on the piece while I'm cutting.
>>
>>2870069
Use a pry bar to open the hinge until the first click point.
Slide door over open hinge.
Close (or open) door.
Done.
>>
>>2870221
>spray a small but constant amount of water on the piece while I'm cutting.
I'm sure your Dremel will love that.
>>
>>2868928
>old thread dead, so reposting in new thread
Long story short, we've ended up with a rabbit that's basically turned into a "yard rabbit" that just roams our property (20 acres), but she likes us and mostly confines herself to the 1 acre area where we hang out.
Is there some kind of cage/hutch mechanic I can build for her easily that she can run into if threatened that will prevent predators (including snakes) from being able to get in?
Some inb4's:
>why do you have her
Another family member wanted her
>why did you let her roam the yard in the first place
I had to look after her for a month while family was away. So she wasn't neglected, I'd let her out and she'd just kind of follow me around as I'd work and come check out what I'm doing. She's very friendly/affectionate. But she's now learnt we're going to put her back in her hutch at night and it's becoming harder and harder to catch her.
>rabbits are gay
She is not old enough to have developed a sexual identity yet and, as an ally, I want her to develop one naturally (provided it's not cis)
Anyone ever built something that can work for this that'll also protect against sneks?
>>
>>2870365
I can probably rig up a splash guard out of clear acrylic or something
>>
File: 617XT+j8JnL.jpg (131 KB, 1500x1391)
131 KB
131 KB JPG
>>2870221
Make a cardboard or thin plywood one of these.
>>
>Asking this on a forum called "do it yourself"
What's a cheap CNC machining service that'll make shitty parts out of UHMW?
>>
>>2869734
>I’d make a work wife out of a femboy that could make a straight cut with a sawzall.
Anon id be you best helper. Id deflect the client for you, make sure the coffee place got your order right, and make sure you never forget a tool.
Also ill be in the driveway 15minutes early before shift so I wont slow you down.
But you better be white, I dont work with minorities.
>>
Any Britons in?

Do Brits really plaster over drywall (what you call plasterboard)? Why? Just to keep plasterers in business? Drywall is already flat. The whole point of introducing it was to make laborious plastering unnecessary. You can just skim and sand the joints and the wall is perfectly ready to paint.

I understand that it makes sense to plaster bricks and blocks and you people have more of that even on interior walls, but watching UK tradies on YouTube I see them plastering drywall on stud walls which is an insane waste of effort IMO.
>>
>>2870892
Because plasterboard is cheap dogshit you can punch through. Plastering over it increases strength, and makes the inner walls line up with the outer walls that are usually solid brick on the majority of houses.

Basically only deanos and retards live in post-war new builds, and they could probably get away without plaster but it's not a big expense and there's a lot of skilled tradesmen that still do it.
>>
Does wood paneling crack as easily as drywall or show movement-related cracks? I recently bought my first house, and the previous owners did a so-so job with the drywall, leaving cracks—some hairline, some up to 1/2" wide. I’ve repaired the foundation and joists, patched the drywall cracks, but they keep coming back.

I'm considering installing wood paneling in some or all rooms anyways. I have a few dozen sheets and I think it's comfy. Would paneling help minimize visible cracks, or is it likely to fail in some way too?
I've enjoyed fixing up the house, but I am so sick of drywall.
>>
How can a door like this be so vandal-proof? Is it because it's made out of hardwood?

https://www.youtube.com/watch?v=ET9SNXpeORY
>>
what's the best glow in the dark pigment available? i want to cast resin with glow powder in it. its something that soothes my autism.
>>
>>2869208
after two lines of coke and two light beers, most tradies will suck each others dicks.
>>
>>2871143
>Is it because it's made out of hardwood?
It's metal.
>>
I like the concept of a heated towel rail / radiator under a basin for a small cloakroom, but I've only found pic related online as an example, but I'm not in love with the Victorian styling, separate taps and all.

Is there any reason why this is a terrible idea that would explain why no one else is apparently doing it?
>>
File: 20241113_122748.jpg (1.44 MB, 2268x3752)
1.44 MB
1.44 MB JPG
>>2871241
>Victorian styling
???

Looks like a pretty standard basic sink to me.

As for why it might be a bad idea: you said it's for a small cloakroom, which will necessitate it being a small sink. I've often found that unless I'm careful when washing my hands in small sinks there will be a small amount of water getting splashed down the front of the sink. Not usually a problem but could become one if that's also where your hand towel is stored. A bit of repeated splashing in a small poorly ventilated room is going to result in towels that smell of mildew.

Pic kinda related, the tiny basin next to my shitter that I'm currently sat on. A literal shitpost.
>>
yo guys, what's your best idea to trick a motion sensor to stay on while I shower?

my bathroom as a timer sensor and it turns off when there's no movement (i'm behind the shower glass door). right now i open the door and wave my hand. but i'm think to attach something to the door so I just need to open/close it to trigger the motion
>>
File: DippingBird_DSC_9142.gif (1.47 MB, 960x916)
1.47 MB
1.47 MB GIF
>>2871268
Infrared emitter stuck on the end of a drinky bird
>>
>>2869422
isn't something like a standard for the size of the speakers?
I mean, not totally detailed and optimized for your speaker type, but enough for the size, 6 1/2,6x9, 8, etc?
>>
>>2869529
How do you simulated it?
>>
File: Battery Work Lights.jpg (102 KB, 1411x1428)
102 KB
102 KB JPG
>>2869940
As told by >>
>>2869953
>>there’s a good chance you could be blowing fuses
Anon, the electrical system of the cars use many amperes (usually), that's why when you use the battery and clamp something into, there is a huge current going into the circuit, you alternator should do just fine, but if your car has a lot of electronics be careful the constant current could degradate the components a bit faster than in normal use, or blowing the fuses.
Perhaps it's less hassle to use a portable flood light (picrel is 50W but guessing they are more out there)?
You can charge before use, and since they are portable they could just work as well as your panel.
Good luck.
Take care.
>>
>>2871268
>a motion sensor to stay on while I shower

replace sensor with one that has on-off-auto switch
AUTO is for a quick piss, ON is for showers
>>
File: mixer.png (2.59 MB, 1422x1976)
2.59 MB
2.59 MB PNG
good morning men of genius
please help me determine the best way to remove the cover from this commercial mixer so I can repack the whole thing with fresh grease. I tried threading a couple screws halfway into the cover plate and pulling it up with some pliers, but it will not budge at all. Based on the exploded view, it looks like I may be able to punch upwards on the central shaft from below, in order to loosen the top cover. I don't really want to hammer on this thing though. What should I try next?
>>
>>2871416
Tried popping these off?
Are you sure there isn't something going through the body that is keeping it place?
>>
>>2871416
>>2871431
I actually just got it off, but thank you for the suggestion! For anyone seeing this in the archive, here's my solution - There were two unoccupied bolt holes next to the bolt holes for the transmission cover. I had to thread a screw into these holes, which then pushed against the casting beneath the cover, pushing the cover upwards. The guide pins were super stuck but I massaged it a little as I applied continuous screw pressure, and it finally popped off
>>
File: PXL_20241113_155549808.jpg (2.07 MB, 4080x3072)
2.07 MB
2.07 MB JPG
Yummy
>>
>>2871363
yeah I may... didn't even realize this when ordering
>>
>>2871439
Hobart machine? You got food grade grease right?
>>
I'm looking for an odd kind of break. A power-on break uses power when the break is enabled, while a power-off break only uses power to disable the break. I'm looking for a break design that would only use power when switching between off and on, a kind of "power-toggle" break.
>>
>>2871443
This is an Avantco knockoff ( MX20, ) good eye. This is the original grease I believe, the paint leads me to believe I'm the first one in here since initial assembly. Yes I'll be repacking it with food grade thanks for looking out
>>
I've got a barn attic to insulate. I'm trying to do this as cheaply as possible since this isn't exactly a top tier build here. I was looking at loose fill insulation, but had a really stupid ass idea, I'll admit, but it might work. I've got access to a big ass source of styrofoam. As in, this place throws away large dumpsters full. Is it worth taking this, shredding it, and using it as loose fill insulation, or is the value of this just utterly garbo/not worth it. This is for a Zone 2 climate, so not exactly ice cold most of the year.
>>
I have an old washing machine and can't figure out what this does.
For reference, it's a Schulthess Super 60, from some time in the 1980s I believe, and it uses metal punch cards for different washing programs.

Unsurprisingly the Internet does not seem to know this washing machine ever existed.
>>
>>2871701
I had a look at some manuals for other random Schulthess machines and found a similar(ish) button on one of their commercial washers. Apparently it's for reduced spinning speed but the manual doesn't elaborate on how to use it.

https://www.manualslib.com/manual/911518/Schulthess-Wsi-100.html?page=22#manual
>>
>>2871707
Zoomed in view so you can see the icon more clearly.
>>
>>2871707
Interesting, thanks. That indeed probably is what it's for. For extra delicate fabrics I imagine.
>>
File: SCR.jpg (646 KB, 2400x1080)
646 KB
646 KB JPG
>>2868928
How would you go on about extracting the heating wire from an electric skillet like the one pic related? Heating element seems to be buried inside the metal tube that's welded to the skillet
>>
File: 1000037351.png (253 KB, 1080x997)
253 KB
253 KB PNG
would this work ? why not ? it's basically a steam that uses it's fuel as the steam and also as the heating source
>>
>>2871757
*steam turbine that uses it's own fuel as the steam source
>>
File: stove on the curb.jpg (110 KB, 653x769)
110 KB
110 KB JPG
>>2871717
>extracting the heating wire from an electric skillet

i'd wait for wednesday night and look around neighborhood for some easier prey
>>
>>2870088
my resume is already shit, so they could find plenty if ither reasons not to hire me besides "disabled"
despite my cons, i have a few pros that make me hire-able
my point being that i could never get away with proving "you didnt hire me becuase im disabled"
i just dont wanna miss on labor job opportunities because im fake disabled.

can anyone else chime in?
>>
hello fellow diyers.
my mother is on vacation in Miami and I'd like to ask her to buy a pair of Knipex pliers, as they cost half of the price in my country.
where can i find such place to buy knipex tools?
>>
>>2871757
It would work, it's just...why?

If you use the fuel as a working fluid but aren't actually burning it in a combustion chamber of some kind, there's no theoretical difference from just using an entirely separate burner. In practice, you're going to have problems with multiple things, not the least of which is that the amount of fuel you need to burn to heat up the compressed fuel and the amount of compressed fuel you need to spin the turbine are going to be wildly different. You'd have to waste loads of fuel either in a a deliberately inefficient heat exchanger or just outright dump it instead of burning it. Consider that (as a ballpark example) a 1l engine, at fill tilt, might be pushing multiple thousands of liters a minute of gas through its exhaust, yet only be consuming hundreds of grams of fuel in the same period.

Depending on what you're using as fuel, you may also have problems with it decomposing at elevated temperatures and lubrication, IDK.
>>
>>2871920
Northern Tool maybe? There’s a couple near Miami depending where she is, but they’re not super close to Miami Beach or any tourist places. Not many brick & mortar chains carry much Knipex… probably because normies don’t want to pay the premium and thieves will steal the most expensive pliers. There might be some smaller mom & pop tool stores that carry them, but she would have to go on a hunt.

Tbqhwy, if she’s in the US, she should just order off Amazon. Their prices are pretty good and tons of it is fast delivery. Only thing I would say is to try to buy stuff “Sold & Shipped by Amazon” and not some random 3rd party company that’s going to send chinesium knockoffs.

>>2871909
Just go do good in the interview, the disability stuff shouldn’t even come up in the process.
>>
>>2871920
>>2871945
Forgot about that North Miami store. I know the Pompano Beach one (about 30min north of Miami if traffic is smooth, which it often isn’t) has an ok selection of Knipex. You can probably check store stock online. But Northern Tool’s prices tend to be a little more expensive than Amazon.
>>
>>2871920
>>2871947
Here’s a pic of the Knipex selection at the Pompano Northern Tool from about a year ago, assuming they didn’t change it. Up to you if you want to send her to NT or Amazon.com
>>
I want to apply clear high gloss lacquer to my recently sanded pine table. It gets used a lot. Is it alright to use a terpentine based lacquer instead of a water based one?

Live in a small apartment. Wondering if the fumes will murder me.
>>
>>2871973
can you laquer it in the parkinglot or somethin?
>>
>>2871924
because water is heavy, if I can master the ratio it would be interesting as a rudimentary but efficient RC car generator
>>
>>2871340
WinISD, but theres various software, that does the math behind. I did not do a 3D FEM sim or anything.
In one of the papers I found an easy formular to estimate tuning of a flared port with a given radius vs a straight pipe. I will measure my a mic after I built the speaker.

>>2871339
Meh, I think it's really worth to match everything to the application to get the most out of it. Most enclosures are designed pretty bad.
>>
what do you do when you feel like you're losing to competition because you can't work fast enough
>inb4 just do better work
yeah but by the law of lowest common denominator better work is not appreciated which means everybody is forced to do similar kinda slop and the only real competition is who can churn it out faster and be most glib about it
>>
>>2872046
Be the best, charge a little bit of a premium, try to get your customers to spread the word with discounts for the referrals and such. If you have a customer that had a bad experience with one of the cheaper guys and you’re coming to fix the work, lean on them real hard to spread the word because their recommendation will be the best for you.
>>
>>2871757
For a second I thought you meant turbine that uses its own fuel as lubricant, which Technical Directions uses in their engines for low cost/weight.
>>
File: unicorn.jpg (19 KB, 570x455)
19 KB
19 KB JPG
I know it's a long shot, but can someone please give me a link/download for a large papercraft(atleast 5 feet in height) that is exactly of near-enough like the one in picrelated?
Any stl file with low poly count would do as well.
I need it for a uni project but can't, for the life of me, find anything good that isn't locked behind a paywall.
>>
>>2872073
>>/po/ should help you out, unless a crossposter is here. Their threads stay up forever.
>>
>>2872075
I remembered that it existed shortly after posting this.
Made a thread there as well now but I think that place might be a tad inactive.
>>
>>2871973
Fumes are flammable
Do it when you can open all the windows
>>
>>2872077
Feel like they had some mega thread with links, I remember looking for a tank there before.
Dare I ask why you need a lowpoly 5ft horse for school?
>>
>>2872084
tl;dr, we have an event coming up in my univerity and my club wants to make a large 3D model of an unicorn/pegasus.
Initially, I thought we would simply be making one out of styrofoam or something but the final decision is that we're making a large origami/papercraft-type shit.
>>
>>2871950
thanks!!
>>
>>2871995 no
>>2872079 thnx
I swallowed my pride, returned it and bought water based lacquer instead.
>>
>>2872048
yeah but how to work fast
>>
>>2871973
What do you pretend to achieve with the lacquer? And why do you prefer oil based?
>>
im thinking about making a ladder. a 20ft tall ladder from 2x4 or 6s. 2, 10ft pieces joined with a scarf joint and then I would place a section on both sides, a smaller length to fit between rungs spaced 10 inches apart. the rungs will be supported with a section under each end. it will be for going and placing a squirrel box on a tree. seem reasonable? I weigh a bit over 220 and im tying to save some money. A fiberglass ladder for my weight is around $200
>>
I went to turn off my outside spigot for the season and after turning off the valve in the basement I go outside to drain what's left in that portion of the line from the spigot and nothing is coming out. I assume there's a bow in line somewhere (it's shitty pex). Rather than try to rip out the entire line is there something I can attach to a standard spigot head to siphon any remaining water?
>>
>>2872119
Smoother finish because it dries slower and it is tougher.
>>
>>2872178
>nothing is coming out

same thing happened to me
but there's no kink coz it's copper
i've surmised it's the fact that water doesnt run uphill when you remove the pressure
we may have just made a world-changing discovery, here
>>
File: IMG20241116171957.jpg (2.69 MB, 1966x2621)
2.69 MB
2.69 MB JPG
Uh. So my old light switch looks like this but the one I bought has a separate screw for ground. Two wires on the bottom. What the fuck do I do here? Wires are all black.
>>
>>2872536
>What the fuck do I do here?

dont see what problem needs fixing
the ground screw is a problem?
you can add a short bare wire from the box to the ground screw, or do nothing, as the grounding is already provided by the retaining screws
>>
>>2872546
So I don't have to worry about running any wires to the ground screw on a modern switch? I can just do the live wire on top the same and two on the bottom? Why do I even have two wires on the bottom? I have to replace this switch it's totally dead, just sorta expected it to look a lot different.
>>
>>2872547
Could be feeding two different lights and they just wired them up that way
>>
>>2872549
Makes sense but not sure what it feeds since I'm looking at the other switch in this box and it also has two on the bottom.

I have been reading that if the box is metal then it might already be grounded through the screws. I wonder if that's what is going on here. If it's fair game just to wire it up like that on a modern switch then I can do that and report back. I'll have to look
>>
File: maxresdefault(1).jpg (104 KB, 1280x720)
104 KB
104 KB JPG
Newbie here, I bought a 150w rotary tool today. After coming home I plugged it in, turned it on and noticed a few things that may or may not be normal
>first time I turned it on, the tool would audibly slow down a bit at times
>there was this mild sparking noise along intermitent audible slowdowns
I did some digging and people were saying that brushed motors need a "break in" period, so I let the tool run at max setting without load for 10 minutes (the manual says to do this when replacing brushes)
>now the tool doesn't slowdown as much
>but I confirmed that there ARE actual sparks inside the motor
>the sparks are probably causing that characteristic "short circuit smell" if there is such a thing
Did some more digging again, and some are saying it's normal and some that it isn't. Thoughts? Should I try to RMA it or not? Or should I try adjusting the carbon brushes? Blow in compressed air? Is this normal for a new motor? Pic unrelated.

If it matters my rooms temp and humidity are 24c and 50%
>>
>>2872555
I did a second break-in run. When I turn it on you can see sparks both at start up and during use (everyone says it's completely normal during start/stop but not so clear about during normal use). There's more sparks at low speed settings than at max settings, does this mean the brushes are not making good contact?
>>
>>2868928
So I have about 5,000 pens sitting here that a job gave me a long time ago.
Not a single one works.
Does anyone know any good solvents I could try to get the ink workable again? Would the glycol esters used for DIY printer ink work with these? And even if I were to find the correct solvent, would it even be possible to get it into the pen at this point?
Acetone and Toluene are already a big no.

>>2872555
>I did some digging and people were saying that brushed motors need a "break in" period
This is correct. Brushes are sort of universalized, so they just manufacture them square and rely on the motor itself to dig the perfect snug contour in during the break in period.
>Did some more digging again, and some are saying it's normal and some that it isn't.
There are a lot of tools that spark, yes. All brushed tools that I'm aware of spark to a certain degree, which is why they require pneumatic tools to work in a lot of jobs with flammable/hazmat conditions.
There is such a thing as sparking TOO much though. If they're shooting out the sides like it's 4th of July you may have other issues. Normally you should just be able to peek through the vents and see the sparks within.

If you're still hesitant, think of it this way: Each of those plates on the commutator, by nature, is going to contact the brush and then stop contacting the brush once it has passed. Every time this happens, you have a miniature arc that occurs no differently than when you pull the plug on any A.C. outlet, you always get that little spark over the air every time something stops contacting.
>>
File: brushespng.png (17 KB, 800x600)
17 KB
17 KB PNG
>>2872577
>dig the perfect snug contour in during the break in period.
Just right now I unscrewed the brush caps to look at them. I think this drawing describes better what I saw. One of the brushes appears to be wearing out evenly, in a curved pattern on both "entrance" and "exit" angles, while the other side is wearing unevenly, I can only see the sparks on one side of the tool by the way so it's probably that side giving me problems. Come to think of it this design is simple but prone to uneven pressure, I reseated the brushes and caps hoping that helps, they weren't screwed all the way down.

>There is such a thing as sparking TOO much though. If they're shooting out the sides like it's 4th of July you may have other issues. Normally you should just be able to peek through the vents and see the sparks within.
>If you're still hesitant, think of it this way: Each of those plates on the commutator, by nature, is going to contact the brush and then stop contacting the brush once it has passed. Every time this happens, you have a miniature arc that occurs no differently than when you pull the plug on any A.C. outlet, you always get that little spark over the air every time something stops contacting.
You're right, but that "sparking TOO much" or "just normal" is what I'm unsure about, this being my first tool. I know and expect a few sparks, but something is probably not right here. It's not a flash bright enough that can be seen from any angle, but something a bit dimmer that you have to look for but is definitely there (and it sure has that "burning wire" smell, the same smell a AC plug makes when it arcs) and the "arcing" sound. I'm not a genius, but I'm pretty sure any constant arcing on any conductor will progressively damage it's conducting ability much like a 'carbonized' AC plug.

My family just went to sleep so I cannot do further testing right now, fug.
>>
File: IMG_9533.jpg (124 KB, 2139x2090)
124 KB
124 KB JPG
>>2868928
Trying to fix my mom's lamp which I suspect has a bad socket, but I have no idea what this fucking thing is. Instead of a typical lamp socket it's got this disc with a plastic extender that holds the light bulb

I should mention the lamp is turned on/off by a light switch on the wall, you don't click/flick anything on the lamp itself.
>>
File: IMG_9536.jpg (317 KB, 2915x2670)
317 KB
317 KB JPG
>>2872641
Here's the same thing but with the plastic extender screwed in. I didn't see anything like that pancake looking thing at Home Depot but I might have been looking in the wrong area
>>
>>2872643
>looking in the wrong area

more like looking in the wrong century
that's a non-standard socket which you must replace with a standard socket
often, it's quite simple as most components are standardized
>>
>>2872641
Have you tested the bulb?
>>
>>2872659
Lol, thanks anon. The bulb is housed in a little glass oil-lamp looking cylinder and then suspended in the air so I thought there'd be some replacement for that disc style specifically - but I guess if it's flicked to "on" permanently then it'll turn on/off per the wall switch anyway. I can't quite tell what your pic wants me to do once I take this little disc off but I'll just go at it

>>2872736
Multiple times. And I'm pretty sure the wiring up to that point is good since I got a little zap when I started fucking with it
>>
File: OrangePiggu23.jpg (192 KB, 1023x919)
192 KB
192 KB JPG
When you tear down drywall, how do you get the screws out of the 2x4s?
>>
what's a good way to get rid of grout waste water that doesn't harm anything?
>>
hello friends! i hope you're all DIYing the fuck out of your day!

i'm making some composite parts using resin infusion and half the time i get air leaks in the vacuum bag
i've come across something called an ultrasonic leak detector and have spent way too long looking for a decent one on ebay/amazon/alibaba/etc. but i have no clue which ones are good and also lots of them are way too expensive

does anybody have any experience with them? are there any decent cheapish ones? i want to know everything!
>>
File: lamp base.jpg (127 KB, 1063x681)
127 KB
127 KB JPG
>>2872741
>I can't quite tell what your pic wants me to do

presumably that tube in the center just unscrews, and you screw in the new base after attaching wires
>>
>>2872590
>You're right, but that "sparking TOO much" or "just normal" is what I'm unsure about
>It's not a flash bright enough that can be seen from any angle, but something a bit dimmer that you have to look for but is definitely there
That sounds about right. I wasn't aware that my drill sparked until I used it in a dimly lit area.
>(and it sure has that "burning wire" smell, the same smell a AC plug makes when it arcs)
That's concerning though, I can't say I've ever had a stinky dremel before so your best bet is to contact the manufacturer and mention that exact thing.

I respect your hesitancy though, sparks are usually something that you don't want to see lol
>>
File: lamp.jpg (352 KB, 1200x1600)
352 KB
352 KB JPG
Thinking of buying this 1930s lamp for restoration. Does the repair on the left arm look like something soft enough to file down?
>>
File: ryan_HELP.png (302 KB, 600x350)
302 KB
302 KB PNG
>>2868928
How the fuck do you remove dishsoap off of tile floors?! My new roommate used what I presumed to be dish soap all of the floors and it was a sticky mess. I tried steam mopping which didn't help as much. I tried putting down white vinegar all over as a steam mopped which helped, but the floor still feels kinda slippery and gunky.

Edit: she says she used some kind of bathroom cleaner, but doesn't remember what. Just that it was from Dollar General.
>>
>>2872885
>remove dishsoap

there's a can of stuff you buy at drugstore for that exact purpose
dunno the name of it, coz i dont do woman's work
>>
>>2872882
>to file down?

if you file it down, the arm's gonna break again
better to cover it up with metal or plastic tubing, and do the same on the other arm so it look original
>>
>>2872791
Got it working, thanks! And you were right - once I pulled it off it was just like replacing any other socket. Now to figure out why it turns on when the light switch is off and vice-versa... when I get to it.
>>
>>2868928
need to replace my toilet seat on this model but ain't having any luck

https://www.winnings.com.au/p/vitra-gloss-white-sline-s70-alto-rear-inlet-toilet-suite-with-pila-slim-seat-117110
>>
>>2872885
>dishsoap off of tile floors
Water
>>
>>2872803
>That sounds about right. I wasn't aware that my drill sparked until I used it in a dimly lit area.
https://www.youtube.com/shorts/rCXZSubwB8o
This is what mine looked right after turning it on for the first time, even after letting it run unloaded for 30 minutes max speed. I reseated the brushes, this time not screwing all the way down and the sparks are almost gone. Some guys in that short are saying that's normal but I don't think it is.

Only problem left is I feel it heats up near the spindle lock, by the looks of it either that's normal because it's pulling hot air from the back to the front vents, or the bearing is bad.

>That's concerning though,
Very, but it also stopped doing that after readjusting the brush-screws, I left them pretty loose. I wonder if what happened was that the springs and the screw were putting TOO much pressure down on the commutator (because sparking went down as speed increased, so the excess pressure wouldn't affect the same), being new and all. It's just weird I guess, the first advice and common sense would be to tighten things down. Oh well, I hope it works hassle free from now on.

Thanks for helping, anon.
>>
Can I cut these sony speaker wires and just splice in similarly gauged audio cable in order to make the wires longer? Never fucked with anything remotely close to this before
>>
>>2873042
Yes. Audio isn't magic, any old cable will do.
>>
I want to wire up a 7 segment display up to a button that cycles from 0 to 9 on button press. What would be a good and compact controller for that?
>>
Half the houses power died. Washing machine outlet, and all lights and outlets past it.

Replaced one breaker and nothing. (Probably a wrong one because the labeling is bad). Replaced the outlet and at first nothing. Replaced a GFCI breaker that was stuck in tripped state. Power returns.....but only for the washing machine outlet I replaced. Everything else is still dead.

Do I need to reseat breakers, are more dead (they can swap to on), are outlets bad? I'm running out of ideas. Shit was browning out for awhile but I thought it was maybe too many things plugged in (computers and heavy draw stuff)
>>
Would it be completely retarded to use this holesaw set (it has carbide teeth) for notching steel tubing: https://sydneytools.com.au/product/bosch-2608900448-expert-14pce-tough-material-hole-saw-set

I wouldn't normally consider it but I can get one of those bosch impact wrench/driver combos on redemption with the saws.
>>
>>2873129
https://www.aliexpress.us/item/2255800302885099.html?gatewayAdapt=glo2usa
these chinkshit ones are surprisingly good and cheap enough to buy spares. they wobble less and cut much better than a shitty holesaw
>>
>>2873088
These days? Just stick an arduino in it.
>>
>>2873129
That impact driver is a literal 50 dollar value on a 300 dollar set of holesaws. How many fucking different holes do you need to notch into tubing, and why can't you just do it with an angle grinder?
>>
What is the name of the top part in English? Its used to clamp the sawblade on a mitre saw with the screw. ‘Arbor ring’ yields no useful results
>>
>>2873144
Arbor nut
>>
File: Clamp, Outer.png (117 KB, 885x492)
117 KB
117 KB PNG
>>2873144
Look online for a diagram and parts for YOUR saw.
For the one I looked up it is an outer clamp.
>>
Can 80v DC kill the fuck out of someone?
I've been fucking with ebike stuff at work and was going to leave the battery connected overnight to the bms to see if it drains it, but if some retard touches the wrong two spots they will receive up to 80v
>>
File: PXL_20241119_015103576.jpg (1.03 MB, 1924x3880)
1.03 MB
1.03 MB JPG
Can someone if this fireproof storage bin.
It's also locked with no keys.
What do I need to pick this one open?
>>
File: PXL_20241119_015404388.jpg (262 KB, 1342x1640)
262 KB
262 KB JPG
>>2873189
>>
File: file.png (5 KB, 970x434)
5 KB
5 KB PNG
I need a corner bracket that can actually go in the corner and connect two perpendicular pieces of wood e.g. the green. The two pieces would be cut at 45 degrees and both attached to the bracket ideally so they both get stability on it

Searched corner bracket and all I get is normal brackets (called corner brackets because they're 90 degrees, but not made for actual corners of rooms)
>>
>>2873189
Almost anything they're wafer locks and pretty crappy.

You could try buying the first result for hg29 that might fit. If you want to try impressioning apparently it's an es1 keyway. Google impressioning key tutorial.
>>
>>2873088
>cycles from 0 to 9 on button press

this one will count up or down as you wish
you'll need to debounce the clock input using a resistor and capacitor
https://www.build-electronic-circuits.com/4000-series-integrated-circuits/ic-4510/
>>
>>2873122
>Half the houses power died

happened to me
there was a fuse box in the basement with two 60A fuses, one for each phase
one was blown
not from over-current, but the insides just came apart from old age
>>
>>2873172
>Can 80v DC kill

almost any voltage (like 9V) can kill if applied at the wrong spot
under normal circumstances 80V will only hurt (like a bitch) and the victim will pull away
and even if they dont die, they're not gonna be happy
so block the area and put up a sign
then it becomes their fault, not yours
>>
>>2873122
Do you have a main breaker outside? Or the main switch on top of your panel? Or one bus bar died. Residential is 240V coming in, which is 120 + 120, so if half of the house is dead, maybe it’s a whole 120 leg somewhere between the utility pole and your fuse panel.

If shit has been browning out for awhile and you don’t own a multimeter to start testing some stuff, I wouldn’t recommend doing much besides flipping the breakers off and back on. Make sure you check for a small panel/disconnect outside where the utilities come into the house, it will be somewhere by the electric meter.
>>
>>2873149
> parts for YOUR saw
They don’t sell Electra beckum parts anymore since Metabo bought their saw design. So I’m trying to check if metabo or any other brand uses compatible ones
>>
>>2873130
they're shallow, the deeper ones a desirable so you don't have to fuck around too much.
>>2873133
show me a brushless bosch driver skin for 50 bucks in aus and I'll buy it. decent holesaws arent cheap and yes, I do have a use case for these.
>>
What are these pressure things called? Are they serviceable?
Mines been leaking for a bit now.
>>
>>2873297
https://www.sloanplumbingparts.com/flushmate-m-101526-f-parts-breakdown
>>
>>2872756
they're really brittle, hit them with a hammer (from the side) and they should break.
you can also probably just unscrew them if you force your cute lil driver bit through the mud.
angle grinder to cut them off if all else fails.
>>
What tool do I need to trace wiring _only_ inside my house? I've seen some reviews/tests for stud finders on youtube, but they beep for anything. Studs, wires, water pipes - you name it. Is there something I can plug in to the outlet (EU) and just follow with a second piece without dismantling everything? I've seen some two-pieced equipment that required both ends of the loop to be open, but I don't want to disconnect everything from my fuse box/electricy central (or whatever it's called in English).
>>
>>2873378
>fuse box/electricy central
Just realized it might be called a home distribution box.
>>
>>2873378
Tone and trace
>>
>>2873378
>(EU)
Search for "AC Circuit Breaker Finder" or whatever you call the device that interrupts power when a fault is detected.
In the US, we plug the transmitter into the live outlet and use the receiver to locate the breaker that powers that outlet.
Depending on the construction of the building and the device you purchase, it may be possible to follow the wiring back to the breaker.
>>
File: 1721155609950390.png (627 KB, 693x632)
627 KB
627 KB PNG
>>2873410
>circuit breaker finder
doesnt everybody just use a U shaped piece of wire?
>>
File: african scientist.webm (585 KB, 640x800)
585 KB
585 KB WEBM
>>2873414
>just use a U shaped piece of wire?

African scientist like you do.
>>
>>2873378
This >>2873399

>>2873410
These don’t trace wire. They beep at the circuit breaker that corresponds to the outlet where the device is plugged in.

I got this cheap Harbor Freight Cen-Tech circuit tracer. I wish I would’ve read the reviews more because I wanted to be able to trace behind walls and it doesn’t work great. I think the issue is some of these tone generator circuit tracers are supposed to be accurate to a point where you can pick one specific wire out in a panel or bunch of wires, so you can only tone it when you get within an inch or two or the wire and it doesn’t work behind walls.
>>
File: wire tracer for $400.jpg (164 KB, 1349x684)
164 KB
164 KB JPG
>>2873432

the 450 model promises to do all the things the 310 fails to do
if somebody's got $400 to burn and a lot of time to engage in worthless pursuits
>>
File: saw.png (338 KB, 803x591)
338 KB
338 KB PNG
Any protips on what I should buy to cut primarily mild structural steel <100mm? I made a rocket stove as babby's first project using just an angle grinder but not keen to do anything bigger or more precise the hard way.

>abrasive chop saw (cheap)
>horizontal or portable bandsaw (either chink or expensive)
>Tungsten carbide cold cut saw (expensive + expensive consumables in my country)

Leaning towards a cheap bandsaw as they seem nicer to use than an abrasive saw but I fear the chink-factor.

For reference my next project will be a welding table
>>
>>2873444
You don’t have to go that expensive. Picrel will work on electical circuits but you gotta make sure you cut the power to it first. Circuit breaker finder works with the power on, and the other tone generators work with no power to trace it to a break. The issue is whether or not it will pick up the tone through your walls and such, which is the issue I have with my cheap HF version
>>
>>2873172
Humans take dc better than ac
300v dc feels like 120v ac

The Indian electrician yt funny man did this in a video where he shocks himself with 300v dc
>>
>>2873469
can you get the next bigger bandsaw? i have a chinkshit one from garbage freight ive been beating on since like 2005. modifications are well documented and theyre easy to fiddle with to make cut straight
>>
>>2872536
That's a 3 way switch wired as a 1-pole
Wire it the same and call it a day
>>
>>2870962
Gotta use mesh tape and 45 minute setting compound (durabond 45) in a house that moves
You might also just have shit insulation and are getting temp/humidity cycling
>>
>>2873485

I won't use it enough to justify the floor space, I really need something that can be stored on a shelf
>>
File: 20241119_225816.jpg (808 KB, 1200x1600)
808 KB
808 KB JPG
i'm trying to clean this monitor case but this white stuff (came from a gypsum plant so likely gypsum) won't go away. it disappears when it gets wet but slowly comes back. i've tried using vinegar and rubbing alcohol and have been scrubbing with a scouring pad. any ideas on how to get it clean?
>>
>>2873532
blowtorch or use some sort of "wipe on plastic renewal" product
>>
>>2873532

wd-40 worked for me
odd, but true
>>
>>2873537
going to try that because i just wasted hours trying to clean it with baking soda which didn't work and i'm getting desperate. i have sewing machine oil and was going to try that next.
>>
>>2870033
My grandpa can't drive anymore and gave me his car with some permanent handicap plates. I haven't changed the registration for the last ~year just for the plates and have yet to suffer for it, including while taking handicap spaces.
>inb4 muh poor cripples need those spaces
I dare anyone to find me an easier people to cross. I say go for it, without a doubt.
>>
File: file.jpg (1.44 MB, 2209x1664)
1.44 MB
1.44 MB JPG
how can i fix these?
gorilla glue doesn't work well
>>
>>2873444
>>2873479
Look around to see if you can hire the test equipment
>>
>>2873588
Gel Super glue and accelerator
>>
>>2873593
how would that work better than gorilla glue?
>>
>>2873588
Drill some holes through both pieces and use some metal brackets and bolts to join them together.
>>
>>2873594
You keep saying gorilla glue like it's one thing. Are you using resin, super glue, plastic glue, wood glue. You need something strong and flexible because it's a high stress area.
>>
>>2872765
Dump into rocks/sand and wash down or let it evaporate
>>
>>2873596
gorilla glue is what i used in the past, with a previous set of headphones, and it didn't work. also i woke up without enough sleep so please forgive me.
>>2873595
it sounds like a decent idea. is it possible to drill in such plastic without it snapping further?
>>
>>2872178
It might be just trapped and will slowly drain over time
I would never have a pex section I expect to drain like that. Copper pipe isn't that expensive for one second like that
>>
>>2873588
Buy new ones because the other side will break soon anyway
>>
>>2873601
i can get shure to replace them for $109, but money's tight rn. i could probably do without for awhile.
>>
>>2873189
it's actually fireproof? if you have paper inside once the temps outside get too hot the paper will just turn to smoke
>>
>>2873416
do you even get shocked when you do something liek this?
>>
how do you take things out of cans like paints etc so it doesn't gunk around the lip
>inb4 spoon
>>
>>2873624
Silicone paint funnel. The tape method has never worked for me.
>>
File: youtube clean can.jpg (117 KB, 569x958)
117 KB
117 KB JPG
>>2873624
>so it doesn't gunk

youtube has about 1 million videos showing diff ways
>>
>>2873632
damm i thought i was the only one with autism
>>
File: Gorilla Glue.jpg (141 KB, 1227x635)
141 KB
141 KB JPG
>>2873596
>You keep saying gorilla glue like it's one thing
>>2873598
>gorilla glue is what i used in the past,
>>
>>2873622
>when you do something liek this
Not being (african) I know to not do this so, NO - I don't get shocked.
>>
>>2873661
Gorilla glue is the foaming polyurethane shit. All that other shit is fake
>>
File: 20241120_194802.jpg (2.83 MB, 1900x2533)
2.83 MB
2.83 MB JPG
Okay, I'm fucking stumped.
How the FUGG am I supposed to seat this on a wooden wall?

There's a wood thread on one end, and machine thread on the other, and I get how I can use a drill to seat the wood screw part into the fence, but then how the fuck do I get the numeral on BOTH machine thread studs?
>>
>>2868928
patent creator didn't have a cat apparently
>>
>>2873671
What does the other side look like? What's the product name
>>
>>2873673
It's a decorative number for a fence.
Generic, no brand name.
>>
>>2873674
Dunno then lad, I'd probably just construction adhesive it to the fence.
>>
>>2873671
>seat this on a wooden wall?

i'd cut off the wood screw section
drill hole
attach machine screw with bolt; brass so it wont rust
looks like an 8-32
>>
>>2873677
>Dunno then lad, I'd probably just construction adhesive it to the fence.

Lol, that's what I'm thinking too. Bostik to the rescue.
>>
File: fake and gay.jpg (125 KB, 1350x699)
125 KB
125 KB JPG
>>2873663
>All that other shit is fake

https://gorillatough.com/
>>
>>2873671
Drill pilot holes.
Drive in/on with soft faced hammer.
>>
>>2873671
>>2873674
This is really annoying me. Where did you buy it? It must have had some packaging?
>>
What is this? It's under a kitchen cabinet. I thought it was a bottle opener but it's not
>>
>>2873759
Probably a mount for one of those little battery powered lights
>>
>>2873687
I don't care about your market9ng bullshit. The only single thing gorilla makes that matters is the original polyurethane glue they popularized. Everything else they make is dog shit just copying other major brands.

Do you call kleenex a disposable nasal towel too or some shit? Fuck off marketing shill. Say the naughty word bot
>>
File: concrete.jpg (81 KB, 845x511)
81 KB
81 KB JPG
I have an old shed with a brick foundation(visible in the pic). Within are tiles that I want to replace with a reinforced concrete slab. Can I just let some guys pour concrete in this if I board up that one gap, put down plastic, steel etc?

Smoothing it out will be a bit harder than usual but not impossible, right?
>>
I've got a project that requires a handful of LEDs and resistors where the fuck can I buy only a handful of them and not a thousand?
>>
File: 031.jpg (146 KB, 1080x901)
146 KB
146 KB JPG
>>2873766
>>
I've got an old, broken Samsung tablet with a screen that's still usable that I'd like to use as an external monitor.
Which LCD driver board should I get?
Screen model: SM-T585_LCD REV 0.1D
>>
>>2873588
Our old friend Matthias has a nice solution.
https://www.youtube.com/watch?v=ziPutFi1BlI
I don't have a power supply but I've done with a soldering iron -- yes I did almost get burned but it worked.
>>
>>2873867
>handful of LEDs and resistors

the usual quality retailers have them starting at qty = 1 but you're gonna pay dearly, like 20 cents a piece, plus shipping
that's digikey, mouser, newark, farnell, octopart
if you have prime, amazon you sell you 100
if you like to take chances to save money, ebay or aliexpress
>>
>>2873959
Rip they're gonna be sitting around for years
>>
I bought a polyester backpack. I want to use it as a tote hybrid so I want to put some handles on it. I looked up leather rivets and the backpack was locally crafted so I have the matching handles. Only problem now is making the holes for the rivets. My question is, do I need to heat the punch so that I can make a hole that immediately self seals and there's no fraying. How much do I need to heat it and how long? Do I immediately pour water on it to cool it?
>>
>>2873671
>>2873677
Those are hanger bolts. They come completely out right?
You install them by putting 2 nuts around the machine side, locked into each other, then drive the outer one with a wrench or socket. It acts as a removable head. The wood screw part goes into a normal pilot hole. They aren't necessary for something like this though. Did they come pre-installed?
>>
>>2874045
Alright I looked it up
https://www.xometry.com/resources/materials/polyester/
It looks pretty frameproof. Do I need to get to 250C?
Is there anything else I should know
>>
File: ezgi_014718.jpg (284 KB, 1200x1200)
284 KB
284 KB JPG
Are tool roll bags good?
>>
File: 20241122_140603.jpg (3.53 MB, 4000x3000)
3.53 MB
3.53 MB JPG
>>2868928
My chair leg gave out and it's a really awkward shape to clamp together, any tips? And do you think wood glue will do it or am I gonna have to shove a new dowel through it or something
>>
>>2874125
Not really since one must unroll them. When you do a task tens, hundreds or more times every efficiency matters. I throw most of those away if I don't cut off extra material then leave them unrolled in a drawer.
>>
>>2874194
That whole leg should be replaced
>>
I need to join some unthreaded aluminium 15mm pipe for an aircon bodge (high pressure system). Can I just make a female to female flared union like I would with copper pipe? Or is there something better?
>>
>>2868928
I'm looking for a flexible fabric NON expanding garden hose 5ft or less, but I can only find them in lengths of 25ft and longer. Does anybody know where I can find something like that?
>>
>>2874387
Just ask a seller on AliExpress, they'll probably custom make one for you
>>
>>2874397
Bro, you're a genius. thank you :*
>>
My ceiling fan just started making an electronic whine when it's on and there's a space heater plugged into the same circuit. I'll try a different heater later but what might be the reason and should I be concerned? Could I put a noise suppression ferrule on the fan control module?
>>
>>2874443
Is the noise still present when the space heater isn't attached? Is the noise present when the fan is on but the space heater is turned off?
>>
>>2874443
>>2874457
Adding to this the whine is most likely a faulty capacitor, so check that out.
>>
>>2872885
You need to keep remopping it with fresh water for several hours. And by mop I mean slop fresh water around, wipe it up, dump the soapy water, wait for it to dry, repeat.
>>
Can I put 7075 t6 aluminum into a 450F oven for an hour or will that screw up the heat treatment?
>>
I want to buy a hobby tractor to move dirt piles and gravel around my yard. The idiots on FB want $20k for the tiniest shittiest 15 hp kubota or john deere. Meanwhile you can get giant machines for the same price. Specifically theres probably a dozen Case 580 backhoes for $20k, some of them have fairly low hours.

Is there any major pitfall to just buying a bigger tractor / loader / backhoe? Ive worked on cars and trucks pretty extensively but this would be my first heavy machinery
>>
>>2874494
The main issues are space and ease of working on something massive, you can't just put it up on jack stands.
>>
>>2874494

>>2857043
>>
>>2874459
So it only does it with that specific heater and only if it's on low. High must be a different circuit.
It just started last night so I might open it up and see if anything looks obviously bad. It's old so capacitors may be the cause
>>
I stupidly tried to spray paint a wooden sword indoors, I don't think I accidentally inhaled too much vapors since I was wearing a mask, but I had to spend time cleaning up the dried spray paint residue (overspray?) which went past the newspaper. Is this residue hazardous or as safe as normal dried paint? I don't intend to do this a second time.

Specifically I was using Rustoleum Flat White Primer Spray & Nippon Pylox Spray paint
>>
>>2868928
Is there any real downside to replacing the belt drive on my drill press with a diy chain drive besides complexity? My drill press is a cheap piece of shit and I don't feel like spending the money on a gear driven one, and all the used ones I find are owned by boomers who "kNoW wHaT i gOt" and won't take less than 80% of the new price for a clapped out old machine.
>>
Best powertool to convert to a gokart motor? Also if I used a battery powered one would it work out fine?
>>
>>2874630
I just checked on Amazon and a 200w dc motor costs less than my extremely cheap power drill. That's a maximally retarded way to do that.
>>
>>2874630
go to u-pull-it and get a cheap auto alternator
>>
>>2874630
The only one I'd even consider doing that with is a chainsaw and that's because you get a sprocket with it, but you'll need to get another sprocket and a chain not covered in cutting teeth anyway. Also you get to use the 40+V batteries.
>>2874638
That may be because the latest drills are putting out around a kilowatt at the high end of things.
>>2874608
Lots and lots of complexity, since you need a chain tensioner and because your motor spindle is probably vertical you'll also need a chain guide between the sprockets. This will also need to be able to be adjusted between the heights of the sprockets to get different speeds, if you care about having different speeds. Also there's no way for the motor to slip if the bit ever gets stuck.
>>
File: file.png (161 KB, 400x400)
161 KB
161 KB PNG
I'm making a table and I just put this on the top & sides of the tabletop. How long should I let it sit before I can handle it enough to flip it over so I can put it on the bottom?
>>
>>2874720
It'll probably say on the can, but I would be willing to bet that it'll be fine if you let it sit overnight. When it's done you'll be able to feel it not being sticky anymore.
>>2873189
It'll take a bit but you can in fact drill out the lock cylinder entirely, and once it's shredded enough, you can remove it, then pull down the latch, and the lock will pop open. You can then buy a replacement, they're cheap. Had to do it before on a file cabinet where the little tab on the back of the cylinder that pulls the latch down broke off.
>>
>>2874726
Can says 4 hours between coats. So I've gotta wait the whole 4 hours before I can finish the bottom, I guess. Okay so that about doubles the time I need for this table, then.
>>
>>2874727
I'd recommend waiting longer than that, that's just the time in which it'll have cured enough for the second coat to not screw up the first coat, not necessarily enough for things you put on the table to not stick to it. But like I said, you'll be able to feel when it's not sticky.
>>
File: file.png (939 KB, 1000x1000)
939 KB
939 KB PNG
Does anyone have a doweling jig to recommend? I would like one that I can center as well as offset. I tried one like pic related but it wasn't centering well and I can't dial in the offset.
>>
what happened to gadgets that deal with annoying people thread? how come something like a signal jammer was not on that list
>>
>>2874832
Because that's illegal territory.
>>
>>2874848
any ideas for hummers, whistler and loud talkers?
>>
>>2873297
>>2873299
Thanks I got the cart out. I got it in a sonic washer. Maybe that may fix things.
How do you get the rest of this tank out? I need to clean the inside
>>
>>2874853
Buttonm seal might be bad
>>
I'm trying to make my own tools and I want to follow this tutorial
https://www.youtube.com/watch?v=m6vdSdN65gE
Only problem is that I can only find 01 tool steel as blocks in my country, not rods
Is there something I can search up which would have similar properties of being shapeable with files/handsaws and hardenable with oil?
>>
>>2874894
Wait never mind I fucking found a source for it
Anyone do anything like this? How difficult is it to fuck up?
>>
>>2874896
Fucking up is part of the process
>>
What am I doing wrong here?

This plastic plunger part with the oring won't seal in that hole. I turn on the water and it flows right into the bowl. It's like it's not even there.
>>
Took it off and flipped it
It's loose and wobbly. It sealing
>>
>>2872550
Would be curious to see how it goes, I'm also dealing with a non-conventional rewire on 2 switches in different rooms coming from the same feed. That does look to be a 3 pole wiring though, you sure there's no mystery switches in your house that it might be for?
>>
Well I got it out.
Not sure why it's not sealing
A new unit is $160
The parts I need are $60. Needs all new seals too
It also needs a lot of cleaning. Previous owners didn't have a water filter.
>>
File: 5035-00.jpg (99 KB, 970x728)
99 KB
99 KB JPG
Anyone know where to get a 6V Lithium rechargeable battery that is only 1-3 Ah? I'm trying to modify something that takes coin batteries to have a large rechargeable battery. I want the amp hours to be small so it's small and wearable.
>>
>>2874989
>Anyone know

just get 2 rechargeable coin cells (or camera cells) available in various ratings
just google the term and provide credit card info
>>
>>2874989
>6V Lithium rechargeable battery

Li-Ion cells fully charged are 4.2V
When the cell reaches 3V, it is fully discharged.
Two cells get you 8.4v and when 6v they are dead.
Li-Pol cells are about the same.
Li-FePO4 cells charge to 3.65v
At 3v. they have 10% of their charge remaining
Two cells go from 7.3v charged to 6v when almost discharged.

There is no easy way to get a 6v rechargeable lithium battery
>>
I need a relatively small low speed (about 100-300 rpm) high torque motor for a prototype, is there something like that available that's not a servo or stepper motor?
>>
File: PXL_20241125_043034925.jpg (1.4 MB, 4080x3072)
1.4 MB
1.4 MB JPG
Is it mold? This is above my shower in apartment
>>
I need to run ac to a caravan on my property
I dont have a separate circuit in my house for ac and the regular sockets are 15amp 240v
can I plug in a rated heavy duty power lead and just run a low kw unit (thinking 1.6kw) from a power socket inside my house?
>>
>>2875016
>Li-FePO4 cells charge to 3.65v
That's a meme. You can feed it 3.65 all you want and as soon as you unplug the charger it will be 3.4ish
Also that is the upper limit it's better to target 3.55 if the pack is in series
>>2874989
Lifepo4 cells. Lithium coin batteries are 3v nominal but fresh out of the package with no load they come as high as 3.7.
Lifepo4 is literally a drop in replacement because it maxes out at 3.65 and it can discharge to 2v which is the end point of the coin cell. You can not get any closer if you tried.
They make them in all kinds of sizes these days
>>
>>2875027
Maybe. Is that moldy silicone hanging?

>>2875048
Probably. Our RV outlets in the US are nornally beefy, but that’s because the regular outlets are 120V and we want to be able to run our RV’s toaster oven and AC at the same time. 1.6kW isn’t a huge load, try to use the shortest extension cord that will work and a beefy gauge.
>>
File: 61gztqMVowL._AC_SL1500_.jpg (129 KB, 1500x1500)
129 KB
129 KB JPG
>>2875007
>>2875016
>>2875051
Thank you for your help! You guys made me realized complicated it will be to make a battery, so I ended up searching more and found this one which I hope works well. It's a little big, but I think I can just attach it to my chest or back instead of my arm.
>>
>>2869940
If you're going to have a car there why not just light up whatever you're doing with the headlights. They'll be brighter than your panel anyway.
>>
How can I make peel-and-stick tiles work for the walls of a shower? They will be going directly on new plywood. Should I use self-adhesive tile primer, or spray gorilla glue or something instead? And do you think like 3 or 4 coats of polyurethane over the whole shit mess would keep the water out?

>inb4 just don't do it, it's a bad idea

I know. Woman has fallen in love with one particular peel and stick tile she found online and insists that is what we use in the shower. I know it's not ideal but I'm wondering if I can make it work by throwing enough adhesives and sealants at it.
>>
I live in a house in the southwest with an unfinished not meant for use one false step in your falling through the ceiling type attic. I want to put some ethernet drops in a couple of the rooms that weren't done when it was built for some reason, and I figured doing it through the attic is preferable to having to try to run it through a hundred feet of walls and corners and shit. how do I NOT fall through the ceiling when up there? do I need to bring up a few sheets of plywood to put across the joists? I know this is /diy/, but how much might it cost to have a pro do it, if only so I'm not paying for it if he decides to do a hey billy impression?
>>
>>2875300
Just step on ceiling joists only.
>>
>>2875300
It'll cost too much to hire a pro, and you can do it yourself easily. Just step on the ceiling joists, it's not hard if you're not a lardass. You can find the wall headers easily enough usually, if you want to do it like a pro, pick up fiberglass cable running rods aka "fish sticks" from Home Depot and fish it down through the walls then cut out your wall plate boxes and install keystone jacks instead of just drilling through the ceiling and running the cord down straight to the devices like a fucking amateur.

Get a headlamp and dust mask, and wear long sleeves. Insulation dust is a bitch.
>>
>>2875301
>>2875305
I have poor balance, probably from huffing too much brake clean with the boys in the garage over the years so the plywood is probably good insurance imo. otherwise I guess I'll give a shot and see if I dont fuck up.
>>
File: s-l1200.jpg (172 KB, 1200x1200)
172 KB
172 KB JPG
Our apartment is cramped and there's no airflow even if all the windows are open. Could I buy an 8in exhaust fan with a hose like picrel, run it once every few days and dangle the hose out of our window to get the musty smeels out?
>>
>>2875319
I guess, but the heat from your fridge or other always on appliances will push air. Hot air rises directing that can create a low pressure zone pulling in air.
>>
Every time I do a stupid job I wish I had a mask with a filter, and every time I can't be bothered buying one. I've got to cut apart some circuit boards in a few days, what's a good mask to buy in the UK? Something with cheap replaceable filters, mouth and nose only because I wear glasses.
>>
>>2875065
Thank you mate appreciate it
>>
>>2875319
Get one of those vornados or dreo fans they're pre good
>>
>>2875469
If you’re just trying to mitigate dust, won’t an N-95 work ok for that? Plenty of those floating around.

Also not sure about the UK, but 3M is everywhere hear. And how shitty Chinese consumables are, even if you get a Chinese respirator, get one that’s a 3M clone and uses 3M filters. They sell a filter for every damn application and chemical and it’s pretty sweet. If you get some chinese one with chinese filters that you can’t find replacements for, it will be a waste of money.
>>
Hey, would it work well to coat corten steel with clear coat? Or would it just fall off or otherwise look terrible?
>>
Smoke Detectors. I had a guy come over to the house and gave a presentation about home fire/water safety. One of the things his kit had was smoke detectors. His were connected and if they went off, you could set it to alert people (neighbors, yourself, etc). The trouble was his kit was several thousand $. Has anyone here heard of such a kit or have a recommendation? I found these on amazon and they interconnect, but I'm curious if there is something else I should look for in these.
>>
>>2875525
There must be ones that go to the Cloud. I know the Blink cameras have a temp sensor and I think I can set those to alert me, or maybe they do automatically above a certain temp. That’s assuming the home still has power and internet though, which is why the stupid security system has a backup 12V battery and hardwired smoke detectors and a monthly fee for some cellular BS alert thing that can work with no phone or cable or power.

>first result on Amazon
>X-Sense wifi smoke detector
There’s a fancy Google Nest version too
>>
>>2875525
If your house catches fire and you're not home, it really doesn't matter if the fire engines get there when the neighbors see smoke or when you get a phone alert. Your house is fucked either way.
>>
Trying to learn how to solder and i cant get the shit to melt.

Using the finest connical tip for smd soldering, cant get it to melt unless the solder is touching the tip. Pcb doesnt seem to heat up at all.

I tried using one of thoose conical tips with a flat side and board still does not heat up to melt solder unless i touch the solder to the tip.

Temps are at 400 C. Using the solder that came with my shit.

Boutta blow my brains out cause even if use fine tips the solder wont properly melt unless i touch it on the body of the tip instead of the tippy rip if that makes sense.

>wb solder paste
No

Maybe i need better solder? Please help
>>
>>2875531
this is true, but it would be good to get an alert and notify the authorities asap! I just figure I may as well opt for those features since I'm looking for new units anyway

>>2875528
Thanks!
>>
File: 4rrq7h.jpg (5 KB, 150x150)
5 KB
5 KB JPG
>>2875558
>cant get it to melt unless the solder is touching the tip.
>>
>>2875558
>Maybe i need better solder? Please help

any retard can solder with extreme ease if they have a good tip and good solder
for example, if you use a blue weller iron, and kester LEADED solder, it'll be a breeze
if you use some cheap no-name crap, it'll be harder that climbing everest
https://youtu.be/QKbJxytERvg

oh, the PCB and components also need to be clean of oxidation
some scubbing will be needed if they were made in 1940
>>
>>2875558
Buy some flux paste in a syringe, it's like a dollar and will help with both heat transfer and oxidation. makes working on old boards much easier. SMD work is tricky if you don't have a feel for how much heat you need and how much heat is too much, or the dexterity to keep pieces aligned.
>>
Where can I buy this caster wheel?
>>
/biz/ laughed at me at the idea of a single person manufacturing shop
>>
>>2875730
>somebody find this for me

>>2678737
>Some friendly suggestions for posting:
>- First ask Google, then ask /diy/. Your question will probably be better received if you do so.
>>
File: fuckedupfile.png (27 KB, 202x171)
27 KB
27 KB PNG
I'm copying pictures and videos from my phone to my computer (via brand new SD card) and the videos look like this and have no picture. The audio is there though. What's causing this? I searched youtube but all the results are for no AUDIO. I have audio, but no picture/video (I'm not sure what you'd call that---I can't see anything)
>>
>>2875786

probably you're relying on Windows codecs, which are very limited
install VLC or MPC-HD
>>
>>2875797
thanks! Does that mean I should use VLC to play the files? I'm running windows 7 so maybe that's part of the issue
>>
File: IMG_6756.jpg (1.59 MB, 4032x3024)
1.59 MB
1.59 MB JPG
I moved a light and patched the ceiling except I can see it now in the light. The drywall looks fine when looking at it straight on and at night. How the fuck do I get orange peel to patch? Do I need a matte ceiling paint to hide this better?
>>
>>2875803
>I should use VLC to play the files?

yes
>>
>>2875759
Hey, if you can handle juggling all the paperwork a business is expected to, including traceability requirements, quality management certification, cybersecurity obligations, finances, the website, social media, and still put out enough pieces of whatever the fuck while paying yourself a living wage and all your taxes and your debts and health insurance, more power to you. It's not impossible depending on what you make, just...I don't think you're going to have a moment to do anything else.
>>
>>2875822
i don't think there is as much red tape unless its pharma or civil
why can't it work like a bespoke clothing store except the crowd favourites are made round the clock and sold later
>>
>>2875835
You can do that, in theory, but you really have to pick what you're doing exactly and pick it very carefully so you actually get enough orders but not too much.
>>
File: corner.jpg (365 KB, 1080x1440)
365 KB
365 KB JPG
Lots of outside corners and door frames appear much lower in temp.
Is this normal? I assume the corners joints is not an insulated area and that with slat construction, the boards are going to be cold.
>>
File: door.jpg (943 KB, 1080x1440)
943 KB
943 KB JPG
I already replaced the door seal, and used foam shims in other areas.
is this expected? 22 year old house.
>>
>>2875819
thank you! I thought I screwed up somehow although that's pretty hard to do considering it's a drag and drop kinda thing!
>>
File: STOP_sign.jpg (136 KB, 555x599)
136 KB
136 KB JPG
This thread has passed the bump limit.

It's currently on page 6

A new thread has been posted here: >>2876379
It's time to transition to the new thread.
>>
>>2876201
>a drag and drop kinda thing!

that's the wrong way to do it - here's the right way
right click on a video file and select Open With, then choose VLC
if the video plays ok, you can set VLC as default video player
right click video file, choose Open With, then Choose Default Program, and select VLC
now, any time you double click a video file of that type, VLC will play it
>>
>>2876390
sweet thank you!!



[Advertise on 4chan]

Delete Post: [File Only] Style:
[Disable Mobile View / Use Desktop Site]

[Enable Mobile View / Use Mobile Site]

All trademarks and copyrights on this page are owned by their respective parties. Images uploaded are the responsibility of the Poster. Comments are owned by the Poster.